How To Clean Dyson V11 Animal Filter Step-by-Step Guide

Welcome to the cleaning party and learn how to clean Dyson V11 Animal Filter! If you own a Dyson V11 Animal vacuum cleaner, you know how important it is to keep it clean.

From pet hair and allergens to general dust and dirt on your beautiful Burber carpet, your vacuum needs regular maintenance to perform at its peak.

In this guide, we’ll look at how to clean the Dyson V11 Animal Filter in just a few easy steps. With a few simple tools, your filter can run like new. Let’s get started!

Locating the Dyson V11 Animal Filter

Whether you’re new to the Dyson family or an experienced user, you may not know where the filter on your Dyson V11 Animal vacuum is located.

The filter is located at the top of the dust cup. Press the ” Filter ” button to access it and slide out the dust cup drawer. At this point, the filter is easily accessible and easily removed.

Remember that your vacuum must be unplugged when you work with the filter for safety purposes.

Now it is safe to remove it from your vacuum and rinse it with cold water. Let it air dry for 30 minutes before putting it back in your machine and vacuuming!

Removing the Dyson V11 Animal Filter

You’ll need to remove the Dyson V11 Animal filter to clean it correctly. The filter should be at the top of the vacuum head and remove it by pressing it down.

Once you have removed the filter cover, remove your HEPA filter and carefully remove it from its casing.

You may notice dirt and debris inside, which is expected, so you need to clean it! To remove all these particles, use a brush or tap the filter against a hard surface to dislodge anything stuck.

If you’re using a brush, ensure you’re gentle and don’t press too hard on the filter.

You don’t want to damage it by brushing too vigorously. Then, add some mild detergent to your HEPA filter in a bucket or container of warm water.

After 10 minutes, rinse with cool water until all suds are gone.

Disassembling the Dyson V11 Animal Filter

Now that you’ve gathered your supplies, it’s time to start cleaning the Dyson V11 Animal Filter.

First up, disassemble the filter. This may sound daunting, but you can take it apart easily with a few simple steps:

Remove the filter cover

Hold the filter cover with one hand then press the release button. The cover should come off quickly; you can put it aside for now.

Take out the old HEPA filter

The old HEPA filter should be located at the bottom of the vacuum cleaner. You can pull it out by gripping both sides of the filter and pulling gently.

Remove any debris from inside

Look inside to ensure there isn’t any debris or dust trapped there, as this could damage your machine and clog up your new filter when you put it back in.

If anything is stuck in there, use a soft brush to remove it.

By taking apart your Dyson V11 Animal Filter carefully and cautiously, you can ensure that all those tricky little parts are taken care of.

As a result, it makes it easy to put everything back together again after cleaning is done!

Cleaning the Dyson V11 Animal Filter Pre-Filter

The pre-filter is the first thing you’ll need to clean when cleaning your Dyson V11 Animal filter. An essential part since it catches dust and dirt particles before reaching the other parts of the filter.

Step-by-step instructions

Unplug your Dyson vacuum cleaner, then disconnect the vacuum cleaner from its power source.

Remove the pre-filter by popping off the cover from the main filter unit (it’s secured with two clips).

Carefully remove it from the filter casing and lay it on a flat surface.

Tap the dust and debris off the pre-filter, or use a vacuum cleaner attachment to suck it clean carefully.

Once it looks like all dust and dirt have been removed, reattach it back onto the main filter unit and pop it back into place using those two clips we mentioned earlier.

Your pre-filter is now ready to use again!

Cleaning the Dyson V11 Animal Filter HEPA Filter

The Dyson V11 Animal Filter HEPA filter is easy to clean and can help extend the life of your vacuum.

How to do it

Remove the filter cap from your Dyson V11 Animal filter by pressing down on the tab and turning it counterclockwise.

Pull out the filter and separate it into two parts by pushing in on the side tabs and lifting off the top part of the filter.

Tap both parts of the filter on a flat surface like a table or countertop to remove debris like dust or dirt.

Rinse the filter under running water and scrub with a soft brush until all traces of dirt, dust, and debris are gone. Ensure you do not use soap or detergent when cleaning your filter!

Shake off any remaining water from both parts of the filter and let them air dry completely before putting them back together in your vacuum.

Regularly cleaning your Dyson V11 Animal Filter HEPA ensures it works as efficiently as possible. Additionally, it can help extend its already impressive lifespan!

Reassembling and Reinstalling the Dyson V11 Animal Filter

Reassemble the Filter

Start by separating the two halves of the filter and lining them up side-by-side.

Locate the three tabs on each half of the filter and ensure they face outwards.

Carefully fit the two halves together until they snap into place.

You should hear a “click” sound once they have been successfully connected back together again.

You can now re-install your filter to your Dyson V11 Animal vacuum cleaner!

Reinstall the Filter

Make sure your vacuum cleaner is turned off before you start this step!

Turn the vacuum cleaner over and locate the dust bin release button –usually at the top of your machine or near one side of it.

Press and hold down this button for 3-5 seconds until you hear a slight “click” sound from within your machine’s body parts (this will indicate that the dust bin has been released).

Pull out the dust bin from within your machine’s body parts – be careful to avoid damaging any cables or other components inside your vacuum cleaner!

Once you have pulled out the dust bin, carefully look for your filter – in most models, this will be located near where one side counterbalance weight is under or near where one side brush bar motor is located above (depending on the model).

Carefully remove any debris that may have built up around/on top of/above/below/around/or close to where your filter is located. Then unclip it from its casing before placing it aside for later re-assembly/cleaning purposes (as mentioned earlier).

Now take your already reassembled filter and place it back into its packing area. Ensuring that all three tabs are correctly lined up with their respective slots so as not to damage them upon insertion back inside your machine body parts area!

Once that has been done, press down firmly for the new filter to slide into place. You should hear another “click” sound when done successfully.

Before closing up the dust bin again by pressing down on both sides equally firmly until both sides snap back into position. You should hear another “click” sound when done correctly!

Congratulations – now you know how to clean the Dysons V11 Animal filter safely and effectively!

Conclusion

 Learning to clean and maintain your Dyson V11 Animal filter is an important skill. It is easy to do and requires minimal supplies and tools.

Most importantly, it helps keep your vacuum in top working order and extend its lifespan.

Following this step-by-step guide, you can easily clean your filter and keep your vacuum functioning optimally.

Regular maintenance can also ensure your vacuum works at its best without running into performance issues. So, now that you know how to clean the Dyson V11 Animal filter, you can get back to enjoying your clean and healthy home.

(Visited 59 times, 1 visits today)